# Components Needed **URL:** \ **Category:** deutsch\ **Created:** [March 6, 2025, 10:21pm UTC](https://forum.fritzing.org/t/components-needed/27516 "2025-03-06T22:21:20Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/letter_avatar_proxy/v4/letter/h/a9adbd/32.png) [@Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/u/Hans_Werner_Atzenhoe)\ **Post date:** [March 6, 2025, 10:21pm UTC](https://forum.fritzing.org/t/components-needed/27516/1 "2025-03-06T22:21:20Z")
Guten Abend , Ich suche einige Teile für eine Wetterstation (inkl.) Gewitter Melder. also Gesucht wird: 1 BME 280 1 BMP 280 1 DHT11 1 ESP8266-Modul das bei Fritzing ist anders Hat jemand was? Mercy im Voraus ---
**Author:** ![vanepp](https://forum.fritzing.org/user_avatar/forum.fritzing.org/vanepp/32/4426_2.png) [@vanepp](https://forum.fritzing.org/u/vanepp)\ **Post date:** [March 7, 2025, 12:09am UTC](https://forum.fritzing.org/t/components-needed/27516/2 "2025-03-07T00:09:55Z")
A google search of the form “fritzing part bme280” turns up a variety of hits, of if you have the data sheet for the one you want I can make a part. The same search with the other 2 part numbers also turn up hits, one of which may do you or again I can make one from a data sheet. Peter via google translate Eine Google-Suche nach „Fritzing-Teil BME280“ ergibt eine Reihe von Treffern. Wenn Sie das Datenblatt für das gewünschte Teil haben, kann ich ein Teil herstellen. Die gleiche Suche mit den anderen beiden Teilenummern ergibt auch Treffer. Einer davon könnte für Sie geeignet sein, oder ich kann wieder eines anhand eines Datenblatts herstellen. Peter ---
**Author:** ![Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/letter_avatar_proxy/v4/letter/h/a9adbd/32.png) [@Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/u/Hans_Werner_Atzenhoe)\ **Post date:** [March 7, 2025, 7:51pm UTC](https://forum.fritzing.org/t/components-needed/27516/3 "2025-03-07T19:51:30Z")
guten Abend Peter, das was ich habe ist wieder von AZ… ![Bildschirmfoto vom 2025-03-07 18-05-29](https://forum.fritzing.org/uploads/default/original/3X/a/b/ab113d950ce850d317677ebb0477b1410a797d20.jpeg) ![Bildschirmfoto vom 2025-03-06 22-58-40](https://forum.fritzing.org/uploads/default/original/3X/b/6/b63c11be41ab12fc5cf9050c754ec279616256a1.png) ---
**Author:** ![Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/letter_avatar_proxy/v4/letter/h/a9adbd/32.png) [@Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/u/Hans_Werner_Atzenhoe)\ **Post date:** [March 7, 2025, 7:54pm UTC](https://forum.fritzing.org/t/components-needed/27516/4 "2025-03-07T19:54:07Z")
![Bildschirmfoto vom 2025-03-07 20-53-41](https://forum.fritzing.org/uploads/default/original/3X/a/e/ae83b9807dfdd55acebe6df6b44262f3f56f2b03.jpeg) ---
**Author:** ![vanepp](https://forum.fritzing.org/user_avatar/forum.fritzing.org/vanepp/32/4426_2.png) [@vanepp](https://forum.fritzing.org/u/vanepp)\ **Post date:** [March 7, 2025, 8:49pm UTC](https://forum.fritzing.org/t/components-needed/27516/5 "2025-03-07T20:49:06Z")
The DH11 looks to be here: > [@Humidity and Temperature Sensor DHT11](https://forum.fritzing.org/t/humidity-and-temperature-sensor-dht11/6307/6): > > OK, your font problem seems mostly to be the fonts were just too small in the svg files (there were translates as well, but that isn’t normally a problem). Breadboard: The layerID breadboard was missing. The only thing I know of that this breaks is exporting the part as an svg or image (the part won’t show up). I rescaled the svg (all of them actually) to be the standard scale. Many existing parts even in core are incorrectly scaled, I’m trying to fix that. The pins should start at 0 (not 8 as… The bmp280 looks to be here: > [@BME / BMP 280 sensor](https://forum.fritzing.org/t/bme-bmp-280-sensor/6143/2): > > Not bad, but a few problems: schematic svg: is missing the schematic layerId none of the connectorxterminal labels are correct. 0 and 1 are still rect and 2 and 3 are labeled 4 and 5. That causes the wire to terminate in the middle of the pin as shown here: [schem] in the fpz file changed type=“pad” to type=“male” edit: also changed lablel from BMP280 to M (for module) The breadboard svg layer ID is bredboard rather than breadboard Here is a part with these things corrected (and schema… and the D1 mini is in core parts here: ![capture](https://forum.fritzing.org/uploads/default/original/3X/7/c/7c2d9b8ca1c999ccba79098e2909c5f8ee23c05b.jpeg) although your image appears to be from the back of the board but the ones on the AZdelivery web site look to be the normal format and thus the one in core parts should do ![capture1](https://forum.fritzing.org/uploads/default/original/3X/2/f/2f74c8028e7e1a17ce705b29b6de1cf6a2341241.jpeg) Peter via google translate Der DH11 scheint hier zu sein: > [@Humidity and Temperature Sensor DHT11](https://forum.fritzing.org/t/humidity-and-temperature-sensor-dht11/6307/6): > > OK, your font problem seems mostly to be the fonts were just too small in the svg files (there were translates as well, but that isn’t normally a problem). Breadboard: The layerID breadboard was missing. The only thing I know of that this breaks is exporting the part as an svg or image (the part won’t show up). I rescaled the svg (all of them actually) to be the standard scale. Many existing parts even in core are incorrectly scaled, I’m trying to fix that. The pins should start at 0 (not 8 as… Der bmp280 scheint hier zu sein: > [@BME / BMP 280 sensor](https://forum.fritzing.org/t/bme-bmp-280-sensor/6143/2): > > Not bad, but a few problems: schematic svg: is missing the schematic layerId none of the connectorxterminal labels are correct. 0 and 1 are still rect and 2 and 3 are labeled 4 and 5. That causes the wire to terminate in the middle of the pin as shown here: [schem] in the fpz file changed type=“pad” to type=“male” edit: also changed lablel from BMP280 to M (for module) The breadboard svg layer ID is bredboard rather than breadboard Here is a part with these things corrected (and schema… und der D1 mini ist in Kernteilen hier: ![capture](https://forum.fritzing.org/uploads/default/original/3X/7/c/7c2d9b8ca1c999ccba79098e2909c5f8ee23c05b.jpeg) Ihr Bild scheint zwar von der Rückseite der Platine zu sein, aber die auf der AZdelivery-Website scheinen das normale Format zu haben, und daher sollte das in Kernteilen ausreichen ![capture1](https://forum.fritzing.org/uploads/default/original/3X/2/f/2f74c8028e7e1a17ce705b29b6de1cf6a2341241.jpeg) Peter ---
**Author:** ![Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/letter_avatar_proxy/v4/letter/h/a9adbd/32.png) [@Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/u/Hans_Werner_Atzenhoe)\ **Post date:** [March 12, 2025, 6:03pm UTC](https://forum.fritzing.org/t/components-needed/27516/6 "2025-03-12T18:03:49Z")
Suche OLED Display 1.3 I2C mit 4 Lötpins + - SDA SCK ![IMG_0015](https://forum.fritzing.org/uploads/default/original/3X/0/a/0a7d5a7878354e533771365cdf6072d4c6886891.jpeg) ![IMG_0014](https://forum.fritzing.org/uploads/default/original/3X/6/2/627e4dfb2572fc691333787045ccb380f392b554.jpeg) ---
**Author:** ![vanepp](https://forum.fritzing.org/user_avatar/forum.fritzing.org/vanepp/32/4426_2.png) [@vanepp](https://forum.fritzing.org/u/vanepp)\ **Post date:** [March 12, 2025, 7:23pm UTC](https://forum.fritzing.org/t/components-needed/27516/7 "2025-03-12T19:23:12Z")
Not enough information here to do much with. Pictures of parts are usually not useful. A web site of the device you want with physical dimensions and connection information is what is needed. In this case this appears to be one of these two parts (note the pin outs are different so you need to select the part that matches the device you have) > [@OLED 128x64 I2C Monochrome Display SSD1306 created](https://forum.fritzing.org/t/oled-128x64-i2c-monochrome-display-ssd1306-created/1202/13): > > In such a case we should make a second part that matches the other common version. Do you have a url to an example of the alternate part? edit: A search of Ebay turns up an even mix of both pin layouts so I have made two new parts, one for each pin out. As you noted it is necessary to make sure you have the correct part for the module you have, because using the other one (and reversing power and ground) will likely burn out your module! Note if you want mounting holes in pcb you need to drag … Peter via google translate Die Informationen reichen hier nicht aus, um wirklich etwas zu bewirken. Bilder von Teilen sind in der Regel nicht hilfreich. Benötigt wird eine Website des gewünschten Geräts mit Abmessungen und Anschlussinformationen. In diesem Fall scheint es sich um eines dieser beiden Teile zu handeln (beachten Sie, dass die Pinbelegungen unterschiedlich sind. Wählen Sie daher das passende Teil für Ihr Gerät aus). > [@OLED 128x64 I2C Monochrome Display SSD1306 created](https://forum.fritzing.org/t/oled-128x64-i2c-monochrome-display-ssd1306-created/1202/13): > > In such a case we should make a second part that matches the other common version. Do you have a url to an example of the alternate part? edit: A search of Ebay turns up an even mix of both pin layouts so I have made two new parts, one for each pin out. As you noted it is necessary to make sure you have the correct part for the module you have, because using the other one (and reversing power and ground) will likely burn out your module! Note if you want mounting holes in pcb you need to drag … Peter ---
**Author:** ![Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/letter_avatar_proxy/v4/letter/h/a9adbd/32.png) [@Hans\_Werner\_Atzenhoe](https://forum.fritzing.org/u/Hans_Werner_Atzenhoe)\ **Post date:** [March 12, 2025, 11:04pm UTC](https://forum.fritzing.org/t/components-needed/27516/8 "2025-03-12T23:04:06Z")
hier ist was … ![Bildschirmfoto vom 2025-03-12 23-44-04](https://forum.fritzing.org/uploads/default/original/3X/b/2/b2964a086ccb365827eb0e0d28627fbbf467c34e.png) ![Bildschirmfoto vom 2025-03-12 23-43-51](https://forum.fritzing.org/uploads/default/original/3X/5/7/57892a0bc93e91ca7a9885bca5a833c657e3243a.png) ![Bildschirmfoto vom 2025-03-12 23-43-21](https://forum.fritzing.org/uploads/default/original/3X/7/8/78aac5f6f98cb59a5b658ea8faf3ae3443fa7cef.png) hoffe das es so langt-